Principle Belt-drive High-End mechanism in special heavy chassis
with structural sound absorber and resonance isolation.
Platter motor Crystal-controlled synchronous motor with precise DSP-controlled optimisation of the motor coil voltage curve
Rotational speeds 33 1⁄3 and 45 rpm
electronically switched
Wow and flutter +/− 0,02%
Rumble 82 dB
Disc platter Pressure-cast aluminium, weight 3,8 kg,
with silicone rubber mat
Bearing technology Hardened, polished steel shaft, close-tolerance plain brass bush
Output voltage 0,75 mV
Channel separation 1kHz 30 dB
Frequency response -3dB 20 Hz – 45 kHz
Terminal impedance 100 Ohm
Stylus compliance 9 µm/mN
Style form Micro Line
Tracking force 20 mN (2 g)
Pickup weight 8 g
Recommended phono amplifier PHE-G R MC
Control interface R2-Link, automatic power-on via amplifier
Mains 100 – 240 V, 50 – 60 Hz, 40 W
Stand < 0,5 W
Optional accessories Disc weight
Disc brush
Phono pre-amplifier
Dimensions (H x W x D) Body 8,2 × 46 × 38 cm
overall 16 × 46 × 38 cm
Weight 14 kg
Finishes Silver anodised aluminium (43), black anodised aluminium (42), brushed
Technical modifications reserved

Contact us for Upgrade options - PHE-R MM or MC phono module (only factory fitted) | Power Three (Carbon) | Power Bar | Audio Triax (Carbon) | PB 10 cleaning brush | AG 10 record stabilizer weight.

MER INFORMATION HÄR

The R-Series
The R-series is T+A’s oldest and most important ­product group. First presented in the year 1992, the system’s technology, operating philosophy and appearance were immediately convincing in every respect, and we were determined to introduce revisions only when genuine improvements were possible.

The new R-series is a completely new development, and for this reason the models bear new type numbers: 2000 R for the low-profile cases, and 2500 R for the taller versions.

The series consists of the PA 2000 R integrated amplifier, the large PA 2500 R integrated amplifier, the MP 2000 R multi-source player and the G 2000 R turntable.

Design Philosophy
During the initial stage of development we leaned towards the concepts, circuits and technologies which make our exclusive High-Voltage (HV) range so outstanding. Although the R-series cases are significantly smaller, we have succeeded in realising very high output powers.

The amplifier stages are of discrete construction, and are based on the HV principle, making them extremely linear, with a very wide frequency range and outstanding transient response.

One of our aims was to achieve high output power, and this required us to develop a mains power supply of very high efficiency, capable of remaining totally stable even when handling peak loads. Therefore the bass reproduction is incredibly precise and controlled independently of the used loudspeakers.

The multi-source player is our universal playback device, based on the technology of our HV series, equipped with a high quality CD transport and capable of coping with a vast range of digital music formats. The converter section is unique: T+A True 1-Bit DSD 512 and 384 kHz PCM.

The classical analogue source is our turntable G 2000 which is available with a modified High-End Carbon tone arm from Clearaudio and two different cartridges.

All the devices can be operated conveniently using the system remote control handset, the radio remote control or alternatively the T+A Control App in conjunction with the MP 2000 R multi-source player.

An Ethernet port for software updates and connection to Home Automation systems is also present.
Although the earlier range of R-series machines had already set the standard for superb quality of casework, the new series surpasses the standard once more.

The entire case, including base cradle, consists of thick-walled aluminum, its components machined from solid metal blocks and extrusions. The external case components are meticulously brushed by hand before being given their hard-anodized finish.

Technology
T+A has carried out the development in two different directions: the one targeted the drive motor, which is required to runs as smoothly and steadily as possible, while the second aimed at avoiding structural sound, resonances and vibration in the system as a whole.

We use a high-quality synchronous motor, whose accurately machined belt pulley drives the disc platter by means of a special ground rubber belt. This arrangement has proved excellent in many applications, and is employed by many other manufacturers of High-End turntables.

However, we were not satisfied with this, and decided to tackle the basic problem of uneven rotational speed right at the root. In contrast to pure vinyl specialists we have great competence in electronic development, which has given us vast experience in using digital signal processors to control complex processes.

Our T+A development team came up with the ingenious idea of using a DSP to fine-tune the curve of the motor coil voltage, with the aim of persuading the motor to run completely smoothly and evenly, devoid of jerks and vibration.

Even the initial rotation of the heavy disc platter is smooth and even, achieved by controlling motor torque. Motor speed fluctuations – known as wow and flutter – are no longer measurable, with the result that the interference commonly associated with uncontrolled motors is completely absent.

Uncontrolled motors are also at the mercy of fluctuations in mains frequency and voltage, but DSP motor control also eliminates this problem.

The innovative system also offers a further major advantage in the form of direct control of rotational speed: the belt no longer needs to be re-positioned manually for the available rotational speeds of 33 and 45 rpm.

The turntable’s case was also designed to eliminate judder and vibration, again with the aim of maximizing sound quality.

For this reason the G 2000 R is housed in a case made of solid MDF, which has excellent damping characteristics; all the sub-assemblies are located in this component.

The turntable body is mounted on four shock absorbers. The external aluminum parts are of sandwich construction in order to absorb structural sound, while the aluminum case cover is bonded to the body, thereby suppressing and absorbing vibration and resonances.

The heavy pressure-cast disc platter is manufactured using an accurate machining tool, fine-turned and mounted on an inner zinc platter for isolation.

The friction of the large support surface isolates the platter perfectly, and prevents any last trace of structural sound.

The heavy disc mat, made of soft silicone rubber, has the same effect, and also avoids damage to the delicate vinyl discs. The net result is that the disc platter is acoustically dead, and offers best possible conditions for the pickup system to make contact with the disc without suffering interference.

The zinc platter can only be produced using the very latest automatic CNC machines, since it undergoes a further precision machining process after the platter shaft has been press-fitted.

This process ensures absolute precision in the whole mechanical system. The plain brass bush and hardened, polished steel shaft are made to a tolerance of 5 μm.